LP150X08 TL A2 PDF
Philips LCD LPXTLA2 datasheets download: a-Si TFT-LCD, “, × , nit, (Typ.), K, 60Hz, CCFL, LVDS (1 ch. Find great deals for LG Philips LPX08 TL A2 15” Laptop LCD Screen. Shop with confidence on eBay!. *When you obtain standard approval, please use the above model name without suffix. LPX *MODEL. TLA2. Suffix. s LCD Co.
|Published (Last):||14 January 2012|
|PDF File Size:||13.89 Mb|
|ePub File Size:||14.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
The lamp power consumption shown above does not include loss of external inverter.
LG Philips LP150X08 (TL)(A2) Screen Display 15 LCD – Grade A+
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. Do not expose the module to sunlight or fluorescent light.
Search the history of over billion web pages on the Internet. Color Input Data Reference The brightness of each primary color red, green and blue is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color.
Delete UJU Connector 0. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter no lighting, flicker, etc lp150c08 occurs. The LP1 50X08 is intended to support applications where thin thickness, low power are critical factors and graphic display are important. It shall help increase the lamp lifetime and reduce leakage current.
s LCD LPXTLA2 Overview –
For more information see FIG 1. Packing Form a Package quantity in one box: Our competitors sell “refurbished” screens when in fact their screens are used or non-refurbished. Surface luminance is the average of 5 points across the LCD surface 50cm from the surface with all pixels displaying white. This is subject to change without prior notice.
Make certain that treatment persons are connected to ground through wrist band etc. Transparent protective plate should have sufficient strength in order to the resist external force. The voltage above VS should be applied to the lamps for more than 1 second for start-up. The matrix employs a-Si Thin Lp150x8 Transistor as the active element.
Cheap Galaxy Ace Lcd Screen Best Lcd Screen for Galaxy Mega
Because leakage current is occurred between lamp wire and conducting tape. For more information see FIG 4. Signal Timing Specifications This is the signal timing required at the input of the User connector.
When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. It should be lower than following voltage: The inverter is an external unit to the LCD.
Mark,Weight g typ. Active Area 9 1 10 4 11 12 5 13 FIG. All VCC power input pins should be connected together. The used lamp current is e.
So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. Packing Form a Package quantity in one box: The matrix employs a-Si Thin Film Transistor as the active element. For most people replacing their screen takes about 30 minutes, and we have lots of photos to guide you through the process. And after fading condensation, smear or spot will occur.
When you confirm it, the LCD— Assembly should be operated in the same condition as installed in you instrument. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. Lamp power must be turn on after power supply for LCD and interface signal are valid.
And after fading condensation, smear or spot will occur. Temperature and relative humidity range are shown in the figure below.
It is recommended that they be stored in the container in which they were shipped. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc.
For more information see FIG 1. Write Your Own Review You’re reviewing: Because leakage current is occurred between lamp wire and conducting tape.
The pin configuration for the connector is shown in the table below.