FAIRCHILD FMS7000 PDF

0

Fairchild/ON Semiconductor FMS is available at WIN SOURCE. Please review product page below for detailed information, including FMS price. 2B 1 ? Fairchild Semiconductor Corporation FMS Low Cost Five Channel 4th Order Standard De?nition. FMS part, FMS sell, FMS buy, FMS stock, FMS TSSOP New&Original pars, , Fairchild, +, New parts and Stock on hand.

Author: Nirn Aram
Country: Bermuda
Language: English (Spanish)
Genre: Technology
Published (Last): 10 April 2004
Pages: 333
PDF File Size: 8.89 Mb
ePub File Size: 2.5 Mb
ISBN: 186-4-29132-622-5
Downloads: 29512
Price: Free* [*Free Regsitration Required]
Uploader: Zukora

Internal diode clamps and bias circuitry may be used if AC-coupled inputs are required see Applications section for details. The outputs can drive AC or DC-coupled single ? DC-coupling the outputs removes the need for output coupling capacitors. F, all outputs AC coupled with ?

Price 3 RON – 5 RON

Frequency Response 10 5 0 -5 2 1 Figure 2. Frequency 0. In addition, the input will faicrhild slightly offset to optimize the output driver performance.

The offset is held to the minimum required value to decrease the standing DC current into the faitchild. Typical voltage levels are shown in the diagram below: DC-coupled inputs and outputs 0. If the input signal does not go below ground, the input clamp will not operate. When the input is AC-coupled, the diode clamp will set the sync tip or lowest voltage just below ground. The worstcase sync tip compression due to the clamp will not exceed 7mV.

  DAS UNSICHTBARE KOMITEE DER KOMMENDE AUFSTAND PDF

FMS datasheet & applicatoin notes – Datasheet Archive

The input level set by the clamp combined with the internal DC offset will keep the output within its acceptable range. DAC outputs can also drive these same signals without the AC coupling capacitor. A conceptual illustration of the input clamp circuit is shown below: The internal pull-down resistance is k?

Care must be taken not to exceed the maximum die junction temperature. Refer to the Layout Considerations section for more information. The FMS is speci? Following this layout con? For optimum results, follow the steps below as a basis for high frequency layout: DC-coupled inputs, AC-coupled outputs 0V – 1. F ceramic bypass capacitors? F capacitor within 0. For multi-layer boards, use a large ground plane to help dissipate heat?

For 2 layer boards, use a ground plane that extends beyond the device by at least 0. AC-coupled inputs and outputs External video source must 7.

The video tilt or line time distortion will be dominated by the AC-coupling capacitor. The value may need to be increased beyond ?

  LINEAR SYSTEMS AND SIGNALS BY B.P.LATHI SECOND EDITION 2005 PDF

F in order to obtain satisfactory operation in some applications. AC-Coupling Caps are Optional. Typical application diagram FMS Rev. Dimensions “D” does not include mold flash, protusions faiechild gate burrs. Mold flash protusions or gate burrs shall not exceed 0. Dimension “E1” does not include interlead flash or protusion. Interlead flash or protusion shall not exceed 0. Fairchilv “b” does not include dambar protusion.

Price 3 RON – 5 RON – ElectronicService-SHOP – Page 23

Allowable dambar protusion shall be 0. Dambar connot be located on the lower radius of the foot.

Minimum space between protusion and adjacent lead is 0. Terminal numbers are shown for reference only. Datums — A — and — B — to be determined at datum plane — H —. Dimensions “D” and “E1” to be determined at datum plane — H —. This dimensions applies only to variations with an even number of leads per side. For variation with an odd number of leads per side, the “center” lead must be coincident with the package centerline, Datum A.